View HV070WS1-105_8176064.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(1/3) a4(210 x 297) spec. number s864-1470 product group rev. issue date page title : HV070WS1-105 product specification a4(210 x 297) page hydis technologies of 34 2012.12.20 b tft lcd proprietary note this specification is the property of hydis and shall not be reproduced or copied without the written permission of hydis and must be returned to hydis upon its request 1
(2/3) a4(210 x 297) revision history product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 rev. ecn no. description of changes date prepared 0 ? initial release 2012.04.10 j.h. kim a e1206- f005 ? add line classification on module label no.3 (toc: t, ids: c) 2012.06.25 t.c.kang b e1212- f001 ? change module barcode label (qpn no. - aa070ws1008, made in china) 2012.12.20 t.c.kang 2
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 3 contents no item page 1.0 general description 4 2.0 absolute maximum ratings 6 3.0 electrical specifications 7 4.0 optical specifications 8 5.0 interface connections 13 6.0 signal timing specifications 16 7.0 signal timing waveforms 16 8.0 input signals, basic display co lors & gray scale of colors 19 9.0 3-wire special port in terface (spi interface) 19 10.0 power sequence 26 11.0 mechanical characteristics 27 12.0 mechanical drawing 28 13.0 reliability test 30 14.0 handling & cautions 31 15.0 labels 32 16.0 packing information 34
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 4 1.0 general description 1.1 introduction HV070WS1-105 is a color active matrix tft lcd module using amorphous silicon tft's (thin film transistors) as an active swit ching devices. this module has a 7.01 inch diagonally measured active ar ea with wsvga resolutions ( 1024 horizontal by 600 vertical pixel array). each pixel is divided into red, green, blue dots which are arranged in vertical stripe and this module can display 16.7m colors. the tft-lcd panel used for this module is a low reflection and higher color type. 1.2 features ? fab site : hydis korea ? thin and light weight ? 3.3 v logic power & 16 v back-light power supply ? 1 channel lvds interface ? smd led (20ea) array (botto m side/horizontal direction) ? 16.7m colors (with dither & hfrc) ? need spi control (csb, scl, sda) for module driving ? green product (rohs) & halogen free bl-pwm-out vcc tft lcd panel 1024 600 gate driver dc/dc gamma vcom back light (smd led array) cn2 source driver ldo vdd ledp & ledn cn1 bl-pwm-in lvds input signal vendor[0] vendor[1] ground vcc
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 5 1.4 general specifications parameter specification unit remark active area 153.6(h) 90.0(v) mm number of pixels 1024(h) 600(v) pixels pixel pitch 0.15(h) 0.15(v) mm pixel arrangement rgb vertical stripe display colors 16.7m colors note 1 display mode normally black outline dimension 163.6 ? 0.3(h) 102.9 ? 0.3(v) 2.47 ? 0.2(d) mm note 2 weight 95 (max.) g back-light bottom edge side, 20-leds type note 1 : support 16.7m with dither and hfrc note 2 : without component horizontal outline dimension is some di fferent to customer request which is 162.8 ? 0.3(h) 102.9 ? 0.3(v) 2.47 ? 0.2(d) but outline dimension is confi rm value between hydis and customer 1.3 application ? e-book, etc < table 1. general specifications >
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 operating range storage range -40 -20 0 20 40 60 80 tem p erature ( ) ( 40 , 90 ) (50, 50) (60, 27) 100 80 60 40 20 90 relative humudity 5 (70, 20) 6 2.0 absolute maximum ratings the followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. parameter symbol min. max. unit remarks logic power supply voltage v cc -0.3 v cc +0.3 v back-light power supply voltage v l -0.3 40 v back-light led current i l - 30 ma note 1 back-light led reverse voltage v r -5v operating temperature t op -20 +60 note 1, note 2 storage temperature t sp -40 +70 note 1. ambient temperatur e vs allowable forward current are shown in the figure below. note 2. temperature and relative humid ity range are shown in the figure below. 90% rh max. ( 40 ta ) maximum wet - bulb temperature at 39 or less. ( > 40 ) no condensation. ta=25+/-2 c < table 2. absolute maximum ratings >
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 7 3.0 electrical specifications 3.1 electrical specifications parameter min. typ. max. unit remarks logic power supply voltage v cc 3.0 3.3 3.6 v note 1 logic power supply current i cc - 220 270 ma logic power consumption p c 0.73 0.89 w back-light power supply voltage v l -1617v note 2 back-light power supply current i l -2025ma back-light power consumption p bl - 1.28 1.36 w note 2, 4 high level differential input signal (v cm = 1.2v) v th --0.1v lvds input low level differential input signal v tl -0.1 - - v input voltage range (singled-end) v in 0-2.4v differential input voltage v id 0.1 - 0.6 v differential input common mode voltage v cm ( v id /2) 2.4- ( v id /2) v input current v in -10 - -10 a panel unit life time 50,000 - - hrs without bl,pcb total power consumption p total - 2.01 2.25 w note 1,2,4 < table 3. electrical specifications > notes : 1. the supply voltage is measured and s pecified at the interface connector of lcm. the logic current draw and power consum ption specified is for 3.3v at 25 . a) typ : window xp pattern, b) max : white pattern 2. the supply voltage is measured and spec ified at the interface connector of lcm. the backlight current dr aw and power consumption specified is 16v at 25. the voltage and current val ue means value for chain. 3. pwm frequency and voltage leve l is fixed by customer. 4. backlight power consumption is calculated value for reference (v l i l 4 chains). about maximum power of backlight is 17v 20ma 4 chains = 1.36w
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 8 4.0 optical specifications 4.1 overview the test of optical specificat ions shall be measured in a dark room (ambient luminance ? 1 lux and temperature = 25 ? 2 ) with the equipment of luminanc e meter system (goniometer system and topcon bm-5a) and test unit s hall be located at an approximate distance 50cm from the lcd surfac e at a viewing angle of and equal to 0 ? . we refer to ?=0 (= 3 ) as the 3 o?clock direction (the ?right?), ?=90 (= 12 ) as the 12 o?clock direction (?upward?), ?=180 (= 9 ) as the 9 o?clock direction (?left?) and ?=270 (= 6 ) as the 6 o?clock direction (?bottom?). while scanning and/or ?, the center of the measuring spot on the display surface s hall stay fixed. v cc shall be 3.3+/- 0.3v at 25 ? c. parameter symbol condition min. typ. max. unit remarks viewing angle range horizontal 3 cr > 10 75 85 deg. note 1 9 75 85 deg. vertical 12 75 85 deg. 6 75 85 deg. luminance contrast ratio cr = 0 ? 640 800 - note 2 luminance of white 1 points y w = 0 ? 30 cd/m 2 note 4 340 400 - cd/m 2 white luminance uniformity 9 points ? y9 72 80 - % note 5 white chromaticity w x = 0 ? 0.280 0.301 0.340 note 3 w y 0.310 0.330 0.370 reproduction of color red r x = 0 ? 0.563 0.593 0.623 r y 0.323 0.353 0.383 green g x 0.283 0.313 0.343 g y 0.559 0.589 0.619 blue b x 0.121 0.151 0.181 b y 0.099 0.129 0.159 response time total (t r +t d ) ta= 25 ? c = 0 ? - 50 - ms note 6 cross talk ct = 0 ? - - 2.0 % note 7 4.2 optical specifications
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 9 notes : 1. viewing angle is the angle at which the contrast ratio is greater than 10. the viewing angles are determined for the horiz ontal or 3, 9 o?clock directi on and the vertical or 6, 12 o?clock direction with respect to the optic al axis which is normal to the lcd surface (see figure1). 2. contrast measurements s hall be made at viewing angle of = 0 and at the center of the lcd surface. luminance sha ll be measured with all pixels in the view field set first to white, then to the dark (b lack) state (see figure1). luminanc e contrast ratio (cr) is defined mathematically as cr = luminance when displaying a white raster / luminance when displaying a black raster. 3. reference only / standard fr ont surface treatment measur ed with green cover glass. the color chromaticity coordinates specifi ed in table 4 shall be calculated from the spectral data measured with a ll pixels first in red, green, blue and white. measurements shall be made at the center of the panel. 4. the luminance value of 400 cd/m2 means the brightness of pwm is 100%. the luminance value of 30 cd/m2 means the brightness of lo wer pwm. ctf means that measure brightness at only center point at figure 2.
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 10 figure 1. measurement set up figure 2. uniformity measure ment locations (9 points) optical characteristics measurement setup center of the screen tft-lcd module lcd panel photo detector (minolta ca210) 4.3 optical measurements note 5. the white luminance uniformity on lcd surface is then expressed as : ? y = ( minimum luminance of 9 points / maximum luminance of 9 points ) * 100 refer figure 2 about measurement points * led condition = (duty ra tio 100%, led current 20ma) column row 34 512 990 34 300 566
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 11 figure 3. response time testing tft off(black) tft on(white) tft off(black) tr 100% 90% 10% 0% td
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 12 y a (768, 300) l256 y b (768, 300) 768,150 l31 256,150 y b -y a y b cross-talk (%) = 100 figure 4. cross modulat ion test description view area where: y a = initial luminance of measured area (cd/m 2 ) y b = subsequent luminance of measured area (cd/m 2 ) the location measured will be exac tly the same in both patterns view area note 6. the electro-optical response time meas urements shall be made as figure 3 by switching the ?data? input signal on and off. the ti mes needed for the luminance to change from 10% to 90% is tr, and 90% to 10% is td . note 7. cross-talk of one area of the lcd surface by another shall be measured by comparing the luminance (ya) of a 25mm diam eter area, with all display pixels set to a gray level, to the lu minance (yb) of that same ar ea when any adjacent area is driven dark (refer to figure 4). 768,450 256,450
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 5.0 interface connections 5.1 electrical interface connection cn1 interface connector (df23c-30ds-0.5v(51), manufacture by hirose) pin no. symbol function 1 vcc +3.3v power supply 2 gnd ground 3 vcc +3.3v power supply 4 clk-in-n lvds clock input (negative) 5 vcc +3.3v power supply 6 clk-in-p lvds clock input (positive) 7 gnd ground 8 gnd ground 9 ledp power supply for led [anode] 10 d0-in-n ldvs differential data input 11 ledn power supply for led [cathode] 12 d0-in-p ldvs differential data input 13 gnd ground 14 gnd ground 15 vendor[0] vendor distinguish pin 1

pin no. symbol function 16 d1-in-n ldvs differential data input 17 vendor[1] vendor distinguish pin 2 18 d1-in-p ldvs differential data input 19 csb serial communication chip select 20 gnd ground 21 scl serial communication clock input 22 d2-in-n ldvs differential data input 23 sda serial communication data input 24 d2-in-p ldvs differential data input 25 gnd ground 26 gnd ground 27 bl-pwm-in brightness control signal 28 d3-in-n ldvs differential data input 29 bl-pwm-out backlight dimmer signal 30 d3-in-p ldvs differential data input 13
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 14 5.2 lvds interface lvds transmitter : thc63lvdm83a input signal transmitter interface aa01b- p030va1 remark pin no pin no system (tx) tft-lcd (rx) pin no. r0 51 48 47 out0- out0+ d0-in-n d0-in-p 10 12 r1 52 r2 54 r3 55 r4 56 r5 3 g0 4 g1 6 46 45 out1- out1+ d1-in-n d1-in-p 16 18 g2 7 g3 11 g4 12 g5 14 b0 15 b1 19 b2 20 42 41 out2- out2+ d2-in-n d2-in-p 22 24 b3 22 b4 23 b5 24 hsync 27 vsync 28 de 30 r6 50 38 37 out3- out3+ d3-in-n d3-in-p 28 30 r7 2 g6 8 g7 10 b6 16 b7 18 reserved 25 mclk 31 40 clkout- clk-in-n 4 39 clkout+ clk-in-p 6

(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 15 5.4 data input format 5.3 back-light interface cn2 led fpc connector ( solder type ) pin no. symbol function remark 1 anode1 led anode power supply typ. 16v 2 3 cathode1 led cathode power supply 4 led cathode power supply rgbrgb rgbrgb 1 pixel = 3 dots rgb rgbrgb rgbrgb (1, 1) (2, 1) (1023, 1) (1024, 1) (1, 600) (2, 600) (1023, 600) (1024, 600)

(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 16 6.0. signal timing specifications 6.1 timing specification at hv mode (lvds transmitter input ) item symbol min. typ. max. unit frame rate - 40 60 73 hz frame period t1 624 635 750 lines vertical display time t2 - 600 - lines vertical blanking time t3 - 35 - lines 1 line scanning time t4 1200 1344 1400 clocks horizontal display time t5 - 1024 - clocks horizontal blanking time t6 - 320 - clocks clock rate 1/t7 40.8 51.2 63 mhz

vsd hsd t1 t2 t3 7.0 signal timing waveforms 7.1 vertical input timing w aveforms of interface signal 7.2 horizontal input timing waveforms of interface signal den hsd t4 t5 t7 dclk t6 den
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 17 7.3 lvds rx interface timing parameter the specification of the lvds rx interface timing parameter < table 9, lvds rx interface timing specification> trip5 trip4 trip3 trip2 trip6 trip1 trip0 rx rx rx rx rx rx rx rx rx rx rx trcip vdiff=0[v] vdiff=0[v] rxclkin+/- rxinz +/- * z = 0, 1, 2 item symbol min. typ. max. unit remarks clkin period trcip - 19.53 - nsec input data 0 trip0 -0.4 0.0 +0.4 nsec input data 1 trip1 tricp/7- 0.4 tricp/7 tricp/7+0.4 nsec input data 2 trip2 2 tricp/7-0.4 2 tricp/7 2 tricp/7+0.4 nsec input data 3 trip3 3 tricp/7-0.4 3 tricp/7 3 tricp/7+0.4 nsec input data 4 trip4 4 tricp/7-0.4 4 tricp/7 4 tricp/7+0.4 nsec input data 5 trip5 5 tricp/7-0.4 5 tricp/7 5 tricp/7+0.4 nsec input data 6 trip6 6 tricp/7-0.4 6 tricp/7 6 tricp/7+0.4 nsec
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 18 8.0 input signals, basic display colors & gray scale of colors a total of 16.7m colors are displayed with dither & hfrc us ing 64 gray from 8bit input. colors & gray scale data signal red data green data blue data r0 r1 r2 r3 r4 r5 r6 r7 g0 g1 g2 g3 g4 g5 g6 g7 b0 b1 b2 b3 b4 b5 b6 b7 basic colors black 000000000000000000000000 blue 000000000000000011111111 green 000000001111111100000000 light blue000000001111111111111111 red 111111110000000000000000 purple 111111110000000011111111 yellow 111111111111111100000000 white 111111111111111111111111 gray scale of red black 000000000000000000000000 100000000000000000000000 darker 010000000000000000000000 brighter 101111110000000000000000 0000000000000000 red 111111110000000000000000 gray scale of green black 000000000000000000000000 000000001000000000000000 darker 000000000100000000000000 brighter 000000001011111100000000 00000000 00000000 green 000000001111111100000000 gray scale of blue black 000000000000000000000000 000000000000000010000000 darker 000000000000000001000000 brighter 000000000000000010111111 0000000000000000 blue 000000000000000011111111 gray scale of white & black black 000000000000000000000000 100000001000000010000000 darker 010000000100000001000000 brighter 101111111011111110111111 white 111111111111111111111111
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 19 9.0 3-wire serial port interface (spi interface) this module use 3-wire serial port interface as function configurat ion and parameter setting d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 d15 d14 sda csb scl address[5:0] w/r hi-z data[7:0] delay next transfer 9.1 3-wire command format bit description d15-d10 register address [5:0] d9 w/r control bit. ?0? for write; ?1? for read d9 hi-z bit during read mode. any data within this bits will be ignored during write mode d7-d0 data for the w/r operation to the address indicated by address phase 9.2 3-wire write format msb ls b d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d1 register address [5:0] 0 x data (issued by external controller) 9.3 3-wire read format msb ls b d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d1 register address [5:0] 1 hi-z data (issued by 3-wire engine)
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 20 9.4 3-wire control register 9.4.1 r00 : system control register designation address description mode r0[0] de/sync mode select. mode = ?0?, hsd/vsd mode. mode = ?1?, de mode. (default) dckpol r0[1] dclk polarity control bit dclkpol = ?0? : data sampling at dclk falling edge. (default) dclkpol = ?1? : data sampling at dclk rising edge. grb r0[2] global reset bit. grb=?0?, the controller is in reset state. grb=?1?, normal operation. (default) stbyb r0[3] standby mode selection bit. stbyb = ?0?, timing control, driver and dc-dc converter, are off, and all outputs are high-z. stbyb = ?1?, normal operation. (default) updn r0[4] gate up or down scan control. updn = ?0?, stv2 output vertical start pulse and ud pin output logical ?0? to gate driver. (default) updn = ?1?, stv1 output vertical start pulse and ud pin output logical ?1? to gate driver. (default) shlr r0[5] right/left sequence control of source driver. shlr = ?0?, shift left : last data = s1<-s2<-s3?<-s960 = first data shlr = ?1?, shift left : last data = s1->s2->s3?->s960 = last data (default) - r0[6] reserved pwr_en r0[7] power enable. pwr_en = h, enable pwm, charge pump and vcom buffer.
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 21 9.4.2 r01 : system control register designation address description r1[0] reserved res[1:0] r1[2:1] display resolution selection. res[1:0] = ?01?, for 1024(rgb)*768 display resolution. (dual or cascade) res[1:0] = ?00?, for 1024(rgb)*600 display resolution. (dual or cascade) (default) res[1:0] = ?10?, for 800(rgb)*600 display resolution. (dual or cascade) res[1:0] = ?11?, for 800(rgb)*480 display resolution. (dual or cascade) (601~936 channel disable) bist r1[3] normal operation / bist pattern select. bist = h : bist (dclk input is not needed) bist = l : normal operation (default) dither r1[4] dithering function enable control. dither = ?1?, enable internal dithering function. dither = ?0?, disable internal dithering function. (default) hfrc r1[5] h-frc selection hfrc = h : h-frc enable hfrc = l : h-frc disable (default) if dither = h and hfrc = l : enable only frc/dithering function if dither = l, disable dithering function (h-frc and frc both disable) cabc_en[1:0] r1[7:6] cabc h/w enable pin. normally pull low. when cabc_en = ?00?, cabc off. (default mode) when cabc_en = ?01?, user interface image. when cabc_en = ?10?, still picture. when cabc_en = ?11?, moving image. designation address description r2[5:0] reserved nbw r2[6] normally black or normally white setting. nbw = h : normally black nbw = l : normally white (default) bist r2[7] reserved 9.4.3 r02 : system control register
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 22 9.4.4 r03 : gate on sequence controller register designation address description sel[1:0] r3[1:0] gate on sequence select frame r3[2] frame inverse or not select. frame = ?1?, uniform frame = ?0?, frame inverse (default) - r3[7:3] reserved sel[0] sel[1] pin control function 11 10 01 0 0 z (default) 9.4.5 r0e : test mode (1) designation address description test_mode(1) r0e[7:0] enter test mode (1) test_mode = 8?h5f, enter test_mode = other exit (default) 9.4.6 r0f : test mode (2) designation address description test_mode(2) r0f[7:0] enter test mode (2) test_mode = 8?ha4, enter test_mode = other exit (default)
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 23 9.4.7 r0d : charging time control (3) designation address description oe_width r0d[7:0] inversion type select. enter test mode (1) and (2) first. then r0d setting will be active test_mode = 8?h00, increase charge time 9.4.8 r02 : charge sharing control designation address description eqc_adj r02[7:0] inversion type select. enter test mode (1) and (2) first. then r10 setting will be active eqc_adj = 8?h43, adjust charge sharing time 9.4.9 r0a : bias current control (5) designation address description bias_trig r0a[7:0] inversion type select. enter test mode (1) and (2) first. then r10 setting will be active bias_trig = 8?h28, trigger bias reduction 9.4.10 r10 : inversion architecture designation address description inv r10f[7:0] inversion type select. enter test mode (1) and (2) first. then r10 setting will be active 2line / 1dot = 8?h41 1line / 1dot = 8?h01 (default)
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 24 r38[7:0] pwm_div[3:0] register function 0x0c 000 don?t use. 0x1c 001 1 0x2c 010 2 0x3c 011 3 0x4c 100 4 0x5c 101 5 0x6c 110 6 0x7c 111 7 (default) 9.4.11 r38 : pwm_div setting designation address description pwm_div[3:0] r38[7:0] pwm dimmer frequency step setting in order in maintain the dimming frequency for brightness control at different display resolution (typical 1024 x 600) at normal mode. we will change default value of pwm_div to follow as table display resolution default value of pwm_div res[1:0] = ?00? 111 res[1:0] = ?01? 111 res[1:0] = ?10? 110 res[1:0] = ?11? 100 note : the r6 and r38 register will be available when the r0e and r0f regi ster already had issued. pwm reference frequency (fosc) real pwm frequency of dimo 51.2mhz (typical) pwm frequency = fosc 256 x 128 x pwm_div[2:0]
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 25 9.5 recommend register setting (cabc off mode) register write sequence : r00 (reset) ? r00 (into standby mode) ? r01 (enable frc / dither, cabc off) ? r02 (enable normally black) ? r0e (enter test mode (1)) ? r0f (enter test mode (2)) ? r0d (sdrrs on) ? r00 (release standby mode) if you don?t use register write sequence, it may cause faulty operation. d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 setting remark r000 0 0 0 0 0 0000101001 0x0029 r000 0 0 0 0 0 0000100101 0x0025 r010 0 0 0 0 1 0000110000 0x0430 r020 0 0 0 1 0 0001000000 0x0840 r0e0 0 1 1 1 0 0001011111 0x385f r0f0 0 1 1 1 1 0010100100 0x3ca4 r100 1 0 0 0 0 0001000001 0x4041 2dot inv. r0d0 0 1 1 0 1 0000000001 0x3401 r000 0 0 0 0 0 0000101101 0x002d 9.6 recommend register setting (cabc on mode (moving picture) register write sequence : r00 (reset) ? r00 (into standby mode) ? r01 (enable frc / dither, cabc on) ? r02 (enable normally black) ? r0e (enter test mode (1)) ? r0f (enter test mode (2)) ? r0d (sdrrs on) ? r38 (pwm frequency = 1.5khz) ? r00 (release standby mode) if you don?t use register write sequence, it may cause faulty operation. d15 d14 d13 d12 d11 d10 d9 d8 d7 d6 d5 d4 d3 d2 d1 d0 setting remark r00000000000 0101001 0x0029 r00000000000 0100101 0x0025 r01000001000 0110000 0x04f0 r02000010000 1000000 0x0840 r0e001110000 1011111 0x385f r0f001111001 0100100 0x3ca4 r10010000000 1000001 0x4041 2dot inv. r0d001101000 0000001 0x3401 r38111000000 0011100 0xe01c r00000000000 0101101 0x002d
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 26 10.0 power sequence to prevent a latch-up or dc oper ation of the lcd m odule, the power on/off sequence shall be as shown in below t1 power supply for lcd vcc interface signal vi (lvds signal of transmitter) led power valid data t2 t5 t3 t4 90% 10% 90% 10% 0v 0v t7 t6 notes : 1. when the power suppl y vdd is 0v, keep the level of input signals on the low or keep high impedance. 2. do not keep the interface si gnal high impedance when power is on. 3. back light must be turn on after power for logic and interface signal are valid. initial 3-wire command led on off off parameter value unit remark min. typ. max. t1 0.5 10 ms t2 0 16 ms t3 200 ms t4 200 ms t5 0 ms t6 3 ms t7 400 ms
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 27 11.0 mechanical characteristics 11.1 dimensional requirements figure 5 & 6 (located in 12.0) show s mechanical outlines for the model parameter specification unit active area 153.60(h) x 90.00(v) mm number of pixels 1024(h) x 600(v) (1 pixel = r + g + b dots) pixel pitch 0.15(h) x 0.15(v) pixel arrangement rgb vertical stripe display colors 16.7m display mode normally black outline dimension 163.6 ? 0.3(h) 102.9 ? 0.3(v) 2.47 ? 0.2(d) mm weight 95 (max.) g back-light edge side 20-leds type ( 5 x 4 array) 11.2 polarizer hardness. the surface of the lcd has an coating to reduce scratching. 11.3 light leakage there shall not be visible li ght from the back-lighting syst em around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 150lux. the manufacture shall furnish limit samples of the panel showing the li ght leakage acceptable.
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 28 figure 5. tft-lcd module outlin e dimension (front view) 12.0 mechanical drawing
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 figure 6. tft-lcd module outlin e dimensions (rear view)
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 30 13.0 reliablity test the reliability test items and its conditions are shown in below. no test item conditions 1 temperature and humidity test (operation) 1. ta = 40 /90% 24hr 2. ta = 40 /30% 24hr 3. ta = 0 24hr 2 temperature and humidity cycling (storage) ta = 85 /90%rh (2h) ,-20 (2h),waypoint(25 25% rh turn off humidity control) 12cycle. 144hr 3 thermal shock ta = -40 ? c ? 85 ? c (30min residence), 100 cycle 4 low temperature storage test ta = -40 ? c, 300 hrs 5 low temperature test (operation) ta = -20 ? c, 300hrs 6 biased humidity/heat soak test (storage) ta = 85 ? c /85%, 300hr 7 altitude storage 20000 ft/-40 ? c, 24hr 8 hot start test ta = 85 ? c 1hr, power on/off per 5m, 5 time 9 cold start test ta = -40 ? c 1hr, power on/off per 5m, 5 time 10 mechanical shock 100 g, 6 ms, half sine wave( x, y, z). acceleration measured shock table. 11 mechanical random vibration 3.5 grms, psd =0.025g 2 /hz, 5-500 hz 15 minutes in all axes (x, y, z) 12 4 pt bend test 1. 7 kgf deflection. scribed edge side up 2. 4 kgf deflection. scribed edge side down 13 ring on ring test x kgf applied. load rae:75mm/min 14 esd screen: 150 pf, 330 ohm, +/-15kv air, +/- 8 kv contact. fpc: 100 pfm100 ohm, +/-200v 10 points, 20times/pt 15 functional test page flip script, 2 m flips notes : 1. except form over the conditions of the polarizer specifications. 2. esd test condition is standard of customer system.
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 31 14.0 handling & cautions 14.1 cautions when taking out the module ? pick the pouch only, when taking out module from a shipping package. 14.2 cautions for handling the module ? as the electrostatic discharges may break the lcd module, handle the lcd module with care. peel a protection sheet off from t he lcd panel surface as slowly as possible. ? as the lcd panel and back - light element are made fr om fragile glass (epoxy) material, impulse and pressure to the lcd module should be avoided. ? as the surface of the polar izer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. ? do not pull the interface connector in or out while the lcd module is operating. ? put the module display side dow n on a flat horizontal plane. ? handle connectors and cables with care. 14.3 cautions for the operation ? when the module is operat ing, do not lose mclk, de si gnals. if any one of these signals were lost, the lcd panel would be damaged. ? obey the supply voltage sequence. if wrong sequence is applied, the module would be damaged. 14.4 cautions for the atmosphere ? dew drop atmosphere should be avoided. ? do not store and/or operate the lcd module in a hi gh temperature and/or humidity atmosphere. storage in an elec tro-conductive polymer packi ng pouch and under relatively low temperature atmosphere is recommended. 14.5 cautions for th e module characteristics ? do not apply fixed pattern data signal to the lcd module at product aging. ? applying fixed pattern for a l ong time may cause image sticking. 14.6 cautions for the digitizer assembly ? when assembling fpc connector, do not flip connector past 90 due to possible damage to connector. ? when positioning digitizer underneath driver ic, do not lift driver ic past 90 due to possible damage to drive ic pattern. ? please be warned that during a ssembly of digitizer, the opening or closing of fpc will result in possible electrostati c discharge damage to the led 14.7 other cautions ? do not re-adjust variable resistor or switch etc. ? when returning the module for repair or et c., please pack the m odule not to be broken. we recommend to use the or iginal shipping packages.
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 32 15.0 labels 15.1 product label 1 2 3 4 5 6 no 1. control number no 2. rank / grade no 3. line classification (hydis: h, toc: t, ids: c) no 5. month (1, 2, 3,?, 9, x, y, z) no 6. fg code no 7. serial number no 4. year (5 : 2005, 6 : 2006, ?) 7 x x x x x x x x x x x x x x x x x hydis barcode 01~03 : vendor code 04~14 : qpn 15~16 : manufactured year 17~18 : manufactured week 19~22 : serial number (32 digit/alphabet) customer barcode yy vvv ppppppppppp ww zzzz HV070WS1-105 hydaa070ws10081133zzzz made in china
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 33 15.2 packing label label size: 108 mm (l) ? 56 mm (w) contents model: HV070WS1-105 q`ty: module q`ty in one box serial no.: box serial no. see next figure for detail description. date: packing date fg code: fg code of product model : HV070WS1-105 serial no. : 0000000000000 q?ty : 40 date : xxxx. xx. xx 00 0 00 0 0 000000 type grade year month item-code serial_no fg code rohs mark
(3/3) a4(210 x 297) product group rev issue date tft lcd product b 2012.12.20 spec. number s864-1470 spec title HV070WS1-105 product specification page of 34 34 16.0 packing information 16.1 packing order notes : 1. box dimension: 350mm(w) x 265mm(d) x 320mm(h) 2. package quantity in one box : 40pcs anti static packing bag 20ea module per inner-box lcd module shield bag cushion pad top pad bottom pad out box 40ea module per inner-box assy packing label

▲Up To Search▲

Price & Availability of HV070WS1-105

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]

Mirror Sites : [www.datasheet.hk] [www.maxim4u.com] [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com] [www.gdcy.net]

. . . . .

We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy.

	To Download HV070WS1-105 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .